<!-- https://docs.youtarget.com/advertiser/en/cases/selective-coef.html -->

# Raise or lower the bid on specific placements

> Set a bid coefficient for zones that perform better or worse than the rest, and turn off the weakest ones.

## Goal

Pay more for [zones](https://docs.youtarget.com/advertiser/en/glossary/zone.md) that bring clicks and conversions and less for weak ones, without turning them off completely. To do this, give a zone a [selective coefficient](https://docs.youtarget.com/advertiser/en/glossary/selective-coef.md): the campaign bid in this zone is multiplied by it.

## Before you start

- A campaign with statistics: the section shows only zones where the campaign has already run.
- Optimization is off in the campaign. If it is on, the platform picks the coefficients and you cannot change them manually. For details, see [Bid optimization](../concepts/optimization.md#what-changes-in-the-campaign-after-you-turn-it-on).
- To evaluate by conversions: a [configured postback](./postback.md).

## Steps

1. Open the **Coefficients** section in the left menu and select a campaign. Another way: in the campaign list, open the campaign menu and select **Coefficients**. The section opens with this campaign already selected.
2. In the top right, select a period of up to 30 days. Days are counted in Moscow time. The table shows the zones where the campaign ran during this period, with their statistics. The **Columns** button turns on the **Conversions**, **CR**, **CPA**, **ROI**, **eCPC** and **eCPM** columns. To find a zone, enter its full ID in the **Search by Sources** field: search by part of an ID does not work.

   *Screenshot: The Selective Coefficients section*

3. To change the bid in a zone, hover over the cell in the **Coefficient** column and click the pencil icon. Enter a percentage and click **Ok**. The arrows next to the field change the value by 10%.

   *Screenshot: Editing a zone coefficient*

4. To stop the campaign from buying a zone at all, turn off the toggle in the **Status** column.

Changes are saved immediately; there is no separate save button.

## Result

The campaign bid in the zone is multiplied by the coefficient:

- **100%**: the bid is unchanged. All zones have this value by default.
- **150%**: the bid is one and a half times higher. The campaign wins the auction in this zone more often and pays more per impression or click.
- **50%**: the bid is half as much. The zone gets fewer impressions, each one cheaper.
- **0%**: the campaign does not take part in the auction in this zone.

Allowed values are from 0% to 5000%. If the campaign has other coefficients too, for example by geo or device, they are multiplied. For how the bid affects impressions, see [Auction and bid](../concepts/auction.md).

The platform collects turned-off zones into a blacklist named "Selective coeffs of campaign …". You can see it on the campaign's **Filters** tab. For details, see [Turn off poor placements with a filter](./filters.md).

### All zones at once

- **Reset all coefficients**: set all zones of the campaign back to 100%. The dashboard asks for confirmation: click **Yes, reset coefficients**.
- **Enable all sources**: turn on all turned-off zones, including those not in the table for the selected period. Confirm with **Yes, enable sources**.
- **Upload CSV**: set coefficients from a file. The file replaces all coefficients of the campaign: zones not in the file go back to 100%.

File format: CSV with the `.csv` extension, up to 10 MB. The first row holds the column names, and the separator is a comma. The coefficient in the file is a multiplier, not a percentage: `1.5` means 150%.

```csv
zone_id,coeff
1201:a7f3c9,1.5
1415:9f00ab,0.5
```

## Troubleshooting

| Symptom | Cause | Fix |
| --- | --- | --- |
| The table is empty and the buttons are inactive | No campaign is selected | Select a campaign in the field on the left above the table |
| The zone you need is not in the table | The campaign did not run in this zone during the selected period | Select another period. To exclude a zone without statistics, use a [filter](./filters.md) |
| "Campaign optimization is enabled" above the table, and you cannot change a coefficient | Optimization is on | The platform manages the coefficients. You can exclude zones with a [filter](./filters.md) |
| "Automation is working" above the table, and you cannot change a coefficient | A zone automation rule is active in the campaign | Stop the rule. For details, see [Set up automation rules](./automation.md) |
| "The period is too long. The maximum period = 30 days" | The selected period is longer than 30 days | Shorten the period |
| Search does not find the zone | You entered part of the ID | Enter the full zone ID, for example `1201:a7f3c9` |
| "Value cannot be greater than 5000%" | The coefficient is above the allowed maximum | Enter a value from 0 to 5000 |
| "Value cannot be less than 0%" | The file has a negative coefficient | Enter a multiplier from 0 to 50 |
| "Invalid file type" | The file is not a CSV file | Save the table as `.csv` |
| "File size exceeds the maximum allowable" | The file is larger than 10 MB | Split the file or remove extra columns |
| "Invalid columns in the file…" when you upload a file | The file has no first row `zone_id,coeff`, or the columns are named differently | Fix the first row of the file |
| "Zone Id Duplicate is detected" | The same zone appears twice in the file | Keep one row per zone |

> [!NOTE]
> An empty coefficient in the file counts as zero: the campaign stops buying this zone.

## Next steps

- [Turn off poor placements with a filter](./filters.md).
- [Set up automation rules](./automation.md) so that coefficients change automatically based on statistics.
